LIGHT MOUNTING INSTRUCTIONS
Installation of the mounting bracket depends on the size
of your pool light opening or if you have an existing niche.
STEP 1 Remove the mounting bracket from the back of the light by unscrewing the set screw and releasing the bracket from the bottom hinge.
STEP 2 Attach the mounting bracket to either your existing niche or spa wall.
See Option 1 or 2 above.
STEP 3 Carefully work the silicone ring around the edge of the light. NOTE: Light and silicone ring must be dry before applying the ring to prevent it from falling off when submerged.
STEP 4 Run the power cable through the opening in spa wall or through the back of the niche to the surface where your spa light switch box is located.
STEP 5 Submerge the light and reattach the bottom of the light to the hinge at the bottom of the light bracket. Tilt the light upwards and secure it to the top of the light bracket with the set screw.
LIGHT INSTALLATION INSTRUCTIONS
ATTENTION: If you are currently running a 12V system you will need to disconnect your current transformer and use the included transformer control box when hooking up this light. We recommend using a licensed electrician for installation.
STEP 1 Turn off the circuit breaker to the spa light switch box. Place a non-contact voltage tester against the switch box to verify no power is present.
STEP 2 Disconnect and remove your existing spa light fixture, if applicable.
STEP 3 Refer to the LIGHT MOUNTING INSTRUCTIONS above to install the light. After completing the install, continue to step 4.
STEP 4 (FIGURE 1). Run the light cable and bottom cable from the control box through 3/4” plastic conduit to an outdoor junction box. Match each colored wire (FIGURE 2) and secure with wire nuts. Run the top cable from the control box through 3/4” plastic conduit and connect to the 110V - 230V power source (FIGURE 3). Secure all conduit by inserting into the connectors on the boxes and sealing with silicone caulk.
CAUTION: If you do not use conduit (not recommended) you must seal the open holes on the top and bottom of the Smart Light Control box and junction box to prevent moisture, debris and insects from getting inside which will cause damage to the circuitry.
STEP 5 Mount the junction box and control box to the wall. The control box can be mounted sideways if necessary. NOTE: If the control box is over 50 feet from the Wi-Fi router an extender may be needed to enhance the signal.
STEP 6 Turn on the circuit breaker and then turn on the light. Once the light is on, proceed to the “DOWNLOADING THE APP AND SYNCING THE LIGHT” instructions below.
DOWNLOADING THE LIFE-BULB APP AND SYNCING THE LIGHT
Scan one of the QR codes below with your smart phone camera to download the Life-Bulb app.
Follow these steps to use the app and sync the light. Note: Both your smart phone and Smart Light Control System box need to be within Wi-Fi range to pick up the signal. If your router is greater than 50 feet from the control box you may need a Wi-Fi extender to expand the signal.
STEP 1 Download the Life-Bulb app and then open it. Choose when to allow
Notifications and Agree to the User Agreement and Privacy Policy.
STEP 2 Tap sign-up to register.
STEP 3 Enter your email address, check agree to privacy policy and user agreement, tap Get Verification Code.
STEP 4 Enter the verification code that was sent to your email address.
STEP 5 Set your password then tap done.
STEP 6 Tap “Allow” when you see “Life-Bulb would like to find and connect
to devices on your local network”.
STEP 7 Tap “Continue” when you see “Life-Bulb app is requesting the
following access permissions”.
STEP 8 Tap “OK” when you see “Life-Bulb Would Like to Use Bluetooth”.
STEP 9 IMPORTANT - The app will show “Add Device” but before doing so you need to have the light in pairing mode. To set the light to pairing mode, turn the switch controlling power to the light OFF and ON three (3) times. The light will turn white and begin to flash. Once it is in pairing mode, tap “Add Device”. NOTE: Once the light begins flashing, you will have about 1 minute to pair the light. If the light stops flashing and turns solid before it is paired, you will have to repeat the OFF and ON process until the light starts to flash again. Then proceed with adding the device.
STEP 10 Tap “Continue” when you see “Life-Bulb app is requesting the following access permissions”.
STEP 11 Tap “Allow While Using App” when you see “Allow Life-Bulb to use your location”
STEP 12 Tap “Add” to add device
STEP 13 Enter your Wi-Fi information and tap “Next”. NOTE: Please be sure your wi-fi router password is correct. The app will still try to connect the device even with an incorrect password but after a minute or so you will receive a "device adding timeout" message. You will not receive an "incorrect" password notification if entered incorrectly.
STEP 14 You will see the device being added. Once added successfully tap “Done”
TROUBLESHOOTING TIPS
LIGHT WILL NOT CONNECT TO WI-FI - Both your smart phone and Smart Light Control System box need to be within Wi-Fi range. If you receive one of the below messages, your control box and/or smart phone is too far away from your router and is not picking up your Wi-Fi signal. Since the control box is now mounted to the wall you will need to move the router closer to your control box until it detects the light (device). If you are unable to move the router closer you will need to add a Wi-Fi extender or Mesh Network to expand the Wi-Fi signal.
1) “Network is unavailable, please check the network”
2) ” Life-Bulb” is not showing up on the app
3) “Device Adding Timeout” NOTE: If you receive this message it could also be due to an insufficient password that was entered in step 13. The app will still try to connect the device even with an incorrect password. You will not receive an "incorrect" password notification. Exit out of the screen by clicking the "X" in the upper left corner of the screen. Click on "add device" again and enter the correct password".
If the error message continues you will need to do the following steps to verify that your password is correct.
1) Go to your Wi-Fi settings on your smartphone
2) Find your network name for the router
3) Tap on "forget this device"
4) Tap on your network name under "NETWORKS"
5) Enter your password to reestablish the network
6) Try adding the device (Smart Light) again through the Life-Bulb app
LIGHT WILL NOT TURN ON WITH THE POWER SWITCH - If you previously used your remote to turn off the light you will need to turn the light back on with the remote before you can use the on/off switch to sync the light.
NOTE: We recommend using the app to control the light verses the remote. Wi-Fi is a more reliable signal than the RF technology used by the remote.
SCHEDULING THE LIGHT
You can set days and times for your light to turn ON and OFF. To schedule the light follow the instructions below.
STEP 1 Tap the "schedule" icon in the lower right
STEP 2 Tap on "Schedule"
STEP 3 Tap "Add"
STEP 4 Select the time you want the light to come on. Select the day(s) you want the light to come on
STEP 5 Tap "Switch" and select "Turn on"
STEP 6 Tap "Save" in the upper right corner
STEP 7 Tap "Add" at the bottom and go through the same process to select the time you want the light to turn off. Tap "switch" and select "Turn off". Tap "Save"
NOTE: If you want to receive alerts on your phone when the light turns ON and OFF you can turn on "Notifications"
CONTROLLING THE LIGHT WITH ALEXA OR GOOGLE HOME
Scan one of the QR codes below with your smart phone camera to download the 3rd party Smart Life app, follow the instructions to activate the app to control your light with Alexa or Google Home.
USING THE REMOTE CONTROL
Batteries NOT included. Uses (2) AAA batteries
NOTE: Batteries have a lifespan and we cannot control how long our product will sit in inventory at Amazon. Therefore, we did not want a customer to receive a new product with a dead battery.